Airflow Systems V410 Specifications Page 1

3 OWNERS MANUAL MODEL V410 (INCLUDES VIBRAPULSE CLEANING SYSTEM*) • INTRODUCTION • SPECIFICATIONS • UNPACKING • INSTALLATION •

A3 three phase motor. Consult the motor name plate and verify the line input voltage before attempting to make this change. CAUTION IN LA

A4 MAINTENANCE WARNING ALWAYS DISCONNECT THE UNIT FROM THE POWER SOURCE BEFORE WORKING ON OR NEAR THE MOTOR OR WIRING ASSEMBLIES. LOCK OUT DIS

A5 1 - Hose (2VP2-1012), quantity as required by applicable unit (1 hose per cartridge). Figure

A6 9. Install the new Vibra Pulse hose onto the air cleaner’s hose barb until fully seated against brass hex on barb, see Figure 9. Lub

A7 10. Slide the spring/clamp up over the hose and 3/8” hose barb until it fully seats against the barb’s hex, see Figure 10. 11. Tighten the hose cl

A8 FILTER REPLACEMENT/ REMOVAL FOR CLEANING 1. Turn unit OFF and disconnect from power source. 2. Remove filter access panel. 3. Release filter

A9 IT IS IMPORTANT TO USE ONLY CLEAN AND DRY COMPRESSED AIR TO CLEAN THE FILTERS, OTHERWISE CONTAMINATION TO CARTRIDGE FILTER ELEMENT WILL RESULT. DO

A10 3. Refill with the new adsorber material. After refilling, shake module to pack granules tightly before replacing cover plate to mak

A11 REPLACEMENT PARTS The following section lists typical replacement parts for the Model V410 . If a part is not listed in Table 2, contact your loc

A12 Figure 14. Model V410 filter lifting assembly. Figure 15.

4 ALWAYS USE AIRFLOW SYSTEMS, INC. REPLACEMENT PARTS AND FILTERS TO MAINTAIN WARRANTY. TO ORDER SPARE PARTS CONTACT:

A13 Model V410 general assembly. TROUBLESHOOTING The troubleshooting guide included in this manual is for qualified personnel only. A Motor Trou

A14 NOTES RECORD START UP DATA HERE MODEL: V410 SERIAL NO.:

A15 APPENDIX 1. BRANCH WIRING ... A1 2. MOTOR TROUBLE GUID

A16 MOTOR WIRING GUIDE (BRANCH CIRCUIT) WIRING To connect motor for proper voltage and rotation, refer to connection diagram on nameplate or

A17 HP 115V 230V 115V 230V 115V 230V 115V 230V 115V 230V 1/8 14(16)* 14(18)* 14 14(18)* 10 14(16)* 10 14(16)* 8 14 1/6 14 14(18)* 12

A18 poor connections. 3. Load too high. 3. Check load motor is carrying at

A19 TYPICAL INSTALLATION WIRING DIAGRAM

A20 OWNERS MANUAL ADDENDUM OPTIONAL AUTOCLEAN CONTROLLER SYSTEM MODELS: PC / PC-2 / DC-1 / DC-2 / DT-3000 DT-800 / V-2 / V410 •

A21 PART# 4KT1-1096 (REV 11/98/A/#26-1894)

5TABLE OF CONTENTS 1. Safety...

3 ALWAYS USE AIRFLOW SYSTEMS, INC. REPLACEMENT PARTS AND FILTERS TO MAINTAIN WARRANTY. TO ORDER SPARE PARTS CONTACT:

3 TABLE OF CONTENTS 1. Safety...

3

4READ THIS MANUAL CAREFULLY BEFORE USING AUTOCLEAN EQUIPPED UNIT. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. SAFETY RULES Before installin

5 PREPARATION AND INSTALLATION Through out this manual certain NOTES, CAUTIONS and WARNINGS are used. They are defined as: Note: Used to indicate

5

6 SINGLE PHASE CONNECTION The factory installed AUTOCLEAN control requires a minimum of field wiring in order to operate. All 115 VAC units with f

7 THREE PHASE CONNECTION Three phase connections require the use of a manual or magnetic motor starter to allow the AUTOCLEAN system to operate of

7 Figure 5. (Dual Cartridge with Relay) Figure 6. (Dual Cartridge without Relay)

6 READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OR OPERATE THE MODEL V410 UNIT. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. SAF

8 Figure 7. (DT-3000 with Relay) Figure 8. (DT-3000 without Relay)

8

9 AUTOCLEAN UNIT OPERATION When wired as shown above, the AUTOCLEAN control will sense operation of the air cleaner fan motor. When the motor is t

9

10 MAINTENANCE The AUTOCLEAN system requires no routine maintenance. Refer to the unit Owners Manual for unit required maintenance of the Vibra-Puls

10

7 5. Always disconnect unit from power source before inspecting or servicing. AIRFLOW SYSTEMS SETS THE STANDARD The Airflow Systems Model

A5 OWNERS MANUAL ADDENDUM LATEST VERSION OF THE CLEAN AIR PLENUM WHICH INCLUDES THE STATIC PRESSURE RELIEF VALVE The Local Exhaust & Venti

8 Figure 1.

9SPECIFICATIONS(*): MODEL V410 STD DIM: 36" W x 26" D x 53" H [0.91m W x 0.66m D x 1.35m H] WEIGHT: 680 lb. (STD) [309 kg]

10 INSPECTION AND UNPACKING Inspect your AFS unit for shipping damage immediately upon receipt. Damaged carton(s), broken crate(s), etc. are i

A2 unit (See the MAINTENANCE Section for more details). If any problems are found, consult the TROUBLESHOOTING Section in this manual. ELECTRICAL A